收藏本站
MAX34446
PMBus Power-Supply Data Logger
Group Command
The device supports the group command. With the group
command, a host can write different data to multiple
data stream. All the devices addressed during this trans-
action wait for the host to issue a STOP before beginning
to respond to the command.
devices on the same serial bus with one long continuous
Group Command Write Format
SLAVE ADDRESS 1, COMMAND BYTE, AND DATA WORD FOR DEVICE 1
1
7
1
1
8
1
8
1
8
1
S
SLAVE
ADDRESS
W
A
COMMAND
CODE
A
DATA BYTE
LOW
A
DATA BYTE
HIGH
A
UUU
SLAVE ADDRESS 2, COMMAND BYTE, AND DATA BYTE FOR DEVICE 2
1
7
1
1
8
1
8
1
Sr
SLAVE
ADDRESS
W
A
COMMAND
CODE
A
DATA BYTE
A
UUU
KEY:
S = START
SLAVE ADDRESS 3 AND SEND BYTE FOR DEVICE 3
Sr = REPEATED START
1
7
1
1
8
1
P = STOP
Sr
SLAVE
ADDRESS
W
A
COMMAND
CODE
A
UUU
W = WRITE BIT (0)
A = ACKNOWLEDGE (0)
UUU
SLAVE ADDRESS N, COMMAND BYTE, AND DATA WORD FOR DEVICE N
SHADED BLOCK = SLAVE TRANSACTION
1
Sr
7
SLAVE
ADDRESS
1
W
1
A
8
COMMAND
CODE
1
A
8
DATA BYTE
LOW
1
A
8
DATA BYTE
HIGH
1
A
1
P
Addressing
The device responds to receiving its fixed slave address
by asserting an acknowledge (ACK) on the bus. The
device does not respond to a general call address; it only
responds when it receives its fixed slave address.
Host Sends or Reads Too Few Bits
If for any reason the host does not complete writing a full
byte or reading a full byte from the device before a START
or STOP is received, the device does the following:
1) Ignores the command.
2) Sets the CML bit in STATUS_BYTE.
Maxim Integrated
3) Sets the CML bit in STATUS_WORD.
4) Sets the DATA_FAULT bit in STATUS_CML.
Host Sends or Reads Too Few Bytes
For each supported command, the device expects a
fixed number of bytes to be written or read from the
device. If for any reason fewer than the expected number
of bytes is written to or read from the device, the device
completely ignores the command and takes no action.
Host Sends Too Many Bytes or Bits
For each supported command, the device expects a
fixed number of bytes to be written to the device. If for
11
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
MAX34561EVKIT# EVAL KIT DUAL E-FUSE 24-TQFN
MAX34565EVKIT# KIT EVAL FOR MAX34565
MAX367CWN IC SIGNAL-LINE CIRC PROT 18-SOIC
MAX4080EVKIT+ KIT EVAL FOR MAX4080
MAX4208EVKIT+ KIT EVAL FOR MAX4208
MAX4209EVKIT+ KIT EVAL FOR MAX4209
MAX4210EEVKIT EVAL KIT FOR MAX4210
MAX4273EVKIT EVAL KIT FOR MAX4273
相关代理商/技术参数
MAX3444EAPA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA+ 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA+T 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EASA-T 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EEPA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EESA 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube
MAX3444EESA+ 功能描述:RS-485接口IC 10Mbps Fail-Safe RS-485/J1708 Tcvr RoHS:否 制造商:Texas Instruments 数据速率:250 Kbps 工作电源电压:3.3 V 电源电流:750 uA 工作温度范围:- 40 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube